HQD GDZ SERIES

HQD GDZ Water-Cooled Spindles

Choose a GDZ by its actual support and nose geometry. The range includes 62, 65, 80, 85, 100 and 105 mm bodies, with different lengths, ER interfaces and electrical specifications. A shared diameter or power rating is only the start of a replacement comparison.

When to choose an HQD GDZ spindle

The listed GDZ configurations are water-cooled manual-tool-change spindles. Complete suffixes distinguish bodies, noses and motor data. The GDZ-26-3 configuration is rated at 24,000 rpm / 400 Hz; retain both values when comparing motor data. Read rated speed and frequency together; some models have winding choices while others list one electrical specification.

2.2 kW ER20 configurations

GDZ-23 variants share motor figures but change diameter and assembly. GDZ-24-3 has a 100 mm body and its own current pairs. A matched 2.2 kW / ER20 label cannot settle mount or drive applicability.

Different motor architecture and higher-output points

Retain the four-pole / 800 Hz data on GDZ-24-1C, the 105 mm body on GDZ-24-2, and the 24,000 rpm / 400 Hz versus 30,000 rpm / 500 Hz distinction on GDZ-27 and -27-2.

Compare the complete configuration

Common selection questions

Does body diameter prove the clamp and nose fit?

Locate permitted support surfaces, clamp length where documented, nose datum, overall space and rear fittings on both exact drawings.

Can current be copied from another model with the same power?

Keep each winding pair or electrical specification with the complete code. Resolve GDZ-26-1 using supplied-unit evidence instead of selecting one conflicting marking by similarity.

Do all 24,000 rpm models use the same frequency?

GDZ-24-1C lists four poles and 800 Hz; other listed points can use 400 Hz. GDZ-27-2 has its own 30,000 rpm / 500 Hz specification.

HQD GDZ model comparison

Rated points, curve conditions and electrical data apply to the exact supplied configuration. Compare the mounting datum, tool interface and selected winding with the installation drawing; equal series codes or power ratings alone do not establish interchangeability.

Model / ConfigurationPower / DutySpeedTool InterfaceCoolingDiameter / MountingSelection Detail
GDZ-17B1.5 kW rated24,000 rpm ratedER16Water-cooledØ80 mmKeep 220 V / 6 A and 380 V / 3.5 A as separate complete winding pairs.
GDZ-181.5 kW rated24,000 rpm ratedER11Water-cooledØ65 mmThe listed electrical specification is 220 V / 5 A; a 380 V choice is not established here.
GDZ-18-20.8 kW rated24,000 rpm ratedER11BWater-cooledØ65 mmKeep the -2 model code and ER11B designation with the drawing and accessory request.
GDZ-18B1.5 kW rated24,000 rpm ratedER16Water-cooledØ65 mmRetain the B suffix and ER16 designation in the quote and accessory request.
GDZ-232.2 kW rated24,000 rpm ratedER20Water-cooledØ80 mmKeep 220 V / 8 A and 380 V / 4.4 A as separate complete winding choices.
GDZ-23-12.2 kW rated24,000 rpm ratedER20Water-cooledØ85 mmKeep 220 V / 8 A and 380 V / 4.4 A as separate supplied winding pairs.
GDZ-23-22.2 kW rated24,000 rpm ratedER20Water-cooledØ80 mmKeep 220 V / 8 A and 380 V / 4.4 A as separate complete winding choices.
GDZ-24-1C3.7 kW rated24,000 rpm ratedER20Water-cooledØ100 mmKeep 380 V / 8 A, four poles and 800 Hz together in the electrical review.
GDZ-24-23.2 kW rated24,000 rpm ratedER20Water-cooledØ105 mmKeep 220 V / 12 A and 380 V / 7 A as separate complete supplied pairs.
GDZ-24-32.2 kW rated24,000 rpm ratedER20Water-cooledØ100 mmKeep 220 V / 9 A and 380 V / 5 A as separate complete supplied pairs.
GDZ-26-10.8 kW rated24,000 rpm ratedER11BWater-cooledØ62 mmThe drawing lists 5 A while the nameplate photo shows 3.5 A; confirm the supplied current before drive sizing.
GDZ-26-3 24,000 rpm configuration1.2 kW rated24,000 rpm ratedER11Water-cooledØ62 mmKeep the 24,000 rpm configuration qualifier with GDZ-26-3 in every drawing and quotation request.
GDZ-274.5 kW rated24,000 rpm ratedER20Water-cooledØ100 mmKeep 220 V / 16 A and 380 V / 9 A as separate complete supplied pairs.
GDZ-27-24.5 kW rated30,000 rpm ratedER20Water-cooledØ100 mmKeep 380 V / 9 A, 30,000 rpm and 500 Hz with the -2 model.

ALL SPINDLES

Compare GDZ configurations.

Compare tooling, cooling and operating ratings, then open the exact configuration for your machine.

FILTER SPINDLES

Showing 14 configurations

More filters

Choose a winding voltage, not a voltage shown on a power curve. Ask us if the voltage you need is not listed.

GDZ Water-Cooled Spindles · 14 configurations

Water-cooled spindle configurations for engraving and routing machines. Confirm the collet, winding, cooling circuit and clamp dimensions.

INSTALLATION FIRST

Check the exact model before ordering.

CONFIGURATION & QUOTATION

Request an HQD GDZ spindle quote

Send the complete code and speed configuration, current nameplate, support drawing, nose and connection photos, drive and water-circuit details. Include the selected winding where listed, quantity, destination and accessory or document needs.

A quotation requires the exact model and physical variant, selected winding, tooling, cooling requirements, quantity and destination. For a replacement, include the existing nameplate, mounting dimensions and equipment intended for reuse. CINKR confirms the proposed supply scope, availability and delivery terms by email.

Compare other HQD series

Compare all models →