HQD GDL SERIES

HQD GDL ATC Spindles

Choose a GDL configuration by its toolholder and machine integration. ISO20, ISO25, ISO30, BT30 and BT40 arrangements need their own release, sensing, support and drive checks; rated power alone cannot identify the required ATC assembly.

When to choose an HQD GDL spindle

The listed GDL configurations use automatic tool change with a defined taper interface. Select the exact holder and retention arrangement first, then check the supplied-unit release services, sensing and interlocks with the machine controller. Air and water cooling both appear in this range, so neither the GDL family nor a common taper establishes every connection.

Compact ISO20 / ISO25 arrangements

Compare the mounting and rear assembly of the compact ISO20 configurations, or inspect ISO25 if that holder family is required. An interface change includes retention, magazine and nose-position checks, rather than selecting a taper by power.

BT40 and duty-specific output

Review the BT40 holder architecture, lower documented rated-speed point and complete mounting requirement separately. Where output is conditioned by duty and ambient temperature, retain those conditions alongside the number.

Compare the complete configuration

Common selection questions

Does a matching taper make two ATC spindles interchangeable?

Compare retention, support, nose datum, release services, sensing, wiring, cooling and complete rear clearance. A shared taper is one selection condition.

Can release pressure be copied between GDL models?

Use the exact supplied-unit drawing and instructions. Release, sealing and cooling connections have different roles; retain the documented service with its model.

Is the highest printed power always the continuous rating?

Read the rated point and any S1/S6 and ambient-temperature conditions. Do not remove duty conditions from an output figure or call a maximum-speed value the rated speed.

HQD GDL model comparison

Rated points, curve conditions and electrical data apply to the exact supplied configuration. Compare the mounting datum, tool interface and selected winding with the installation drawing; equal series codes or power ratings alone do not establish interchangeability.

Model / ConfigurationPower / DutySpeedTool InterfaceCoolingDiameter / MountingSelection Detail
GDL100-25-24Z/2.52.5 kW rated24,000 rpm ratedISO25Water-cooledØ100 mmKeep 220 V / 9.2 A and 380 V / 5.5 A as separate winding pairs.
GDL110-30-18Z/3.23.2 kW rated18,000 rpm ratedBT30Water-cooledØ110 mmSelect 220 V / 11.5 A or 380 V / 6.9 A as a complete winding pair.
GDL120-30-24Z/5.55.5 kW rated24,000 rpm ratedBT30Water-cooledØ120 mmChoose 220 V / 19 A or 380 V / 11 A as a complete electrical pair.
GDL125-40-12Z/7.57.5 kW rated12,000 rpm ratedBT40Water-cooledØ125 mmCheck 380 V / 16.5 A and the 600 Hz, six-pole operating information together.
GDL40.5-ISO20-24Z/2.22.2 kW rated18,000 rpm rated / 24,000 rpm maxISO20Air-cooledKeep 18,000 rpm / 300 Hz rated separate from 24,000 rpm / 400 Hz maximum.
GDL70-24Z/9.0 ISO30 · Long nose9 kW at S6-60%, TA20°C24,000 rpm ratedISO30Air-cooledISO30 · Long noseKeep “ISO30 · Long nose” with GDL70-24Z/9.0 in drawings and inquiries.
GDL70-24Z/9.0 ISO30 · Short nose9 kW at S6-60%, TA20°C24,000 rpm ratedISO30Air-cooledISO30 · Short noseState “ISO30 · Short nose” with the base GDL70-24Z/9.0 code.
GDL70-24Z/9.0B9 kW at S1, TA20°C24,000 rpm ratedISO30Water-cooledKeep the B suffix and water-cooled configuration in drawings, comparisons and inquiries.
GDL80-20-24Z/2.2B2.2 kW rated24,000 rpm ratedISO20Water-cooledØ80 mmCheck the 220 V / 7.6 A motor winding with the 800 Hz, four-pole operating information.

ALL SPINDLES

Compare GDL configurations.

Compare tooling, cooling and operating ratings, then open the exact configuration for your machine.

FILTER SPINDLES

Showing 9 configurations

More filters

Choose a winding voltage, not a voltage shown on a power curve. Ask us if the voltage you need is not listed.

GDL ATC Spindles · 9 configurations

Automatic tool change with a defined taper interface. Check the air supply, sensing, toolholder and release sequence for the exact model.

INSTALLATION FIRST

Check the exact model before ordering.

CONFIGURATION & QUOTATION

Request an HQD GDL spindle quote

Send the exact model and nose/configuration, required taper, nameplate, drive model, mount and rear-connection evidence. Include the machine’s release/sensing arrangement, quantity, destination and tooling or document needs.

A quotation requires the exact model and physical variant, selected winding, tooling, cooling requirements, quantity and destination. For a replacement, include the existing nameplate, mounting dimensions and equipment intended for reuse. CINKR confirms the proposed supply scope, availability and delivery terms by email.

Compare other HQD series

Compare all models →