HQD GDK SERIES

HQD GDK Engraving & Milling Spindles

Start with the working speed and applicable power curve. The GDK range includes fixed rated points and documented operating ranges, with ER11 through ER32 tooling and different mounting envelopes. Choose the actual load cycle before comparing the model-code power numbers.

When to choose an HQD GDK spindle

The listed GDK configurations are water-cooled manual-tool-change spindles. Some have separate winding choices; range models can instead show voltage/frequency curve endpoints. Their larger curve output remains tied to the stated duty and ambient conditions. A curve endpoint is not an orderable winding, and a power range in the code does not establish one unconditional continuous rating.

125 mm ER32 configurations

Compare the 12,000–24,000 rpm range with the 30,000 rpm / 1,000 Hz point using its own clamp and drawing references. Retain the 395.5 mm body reference and 85 mm rear projection separately on the latter model.

Compare the complete configuration

Common selection questions

Are two voltage curve endpoints two winding choices?

No. Keep the curve’s U/f information separate from documented supplied winding pairs and confirm the motor specification for the actual unit.

Does the power range in a code prove constant full output?

Use the applicable curve at the working point and retain duty and temperature conditions. The model code is not a substitute for that operating information.

Does front air sealing provide ATC release?

The listed GDK tooling is manual ER. A documented front seal and its pressure are separate from an automatic tool-release system.

HQD GDK model comparison

Rated points, curve conditions and electrical data apply to the exact supplied configuration. Compare the mounting datum, tool interface and selected winding with the installation drawing; equal series codes or power ratings alone do not establish interchangeability.

Model / ConfigurationPower / DutySpeedTool InterfaceCoolingDiameter / MountingSelection Detail
GDK100-12-24Z/2.2-4.42.2 kW rated12,000–24,000 rpmER20Water-cooledØ100 mmKeep 2.2 kW rated separate from the 4.4 kW curve level and S1/S6-20%, TA20°C conditions.
GDK100-24Z/3.23.2 kW rated24,000 rpm ratedER20Water-cooledØ100 mmSelect 220 V / 11 A or 380 V / 6.4 A as a complete electrical pair and check 400 Hz output capability.
GDK105-21Z/3.53.5 kW rated21,000 rpm ratedER20Water-cooledØ105 mmKeep 220 V / 12.1 A and 380 V / 7 A as separate electrical pairs.
GDK105-9-21Z/2.2-5.02.2 kW rated9,000–21,000 rpmER20Water-cooledØ105 mmKeep 2.2 kW rated separate from the 5.0 kW curve level and its S1/S6-20%, TA20°C notes.
GDK110-9-18Z/2.2-4.42.2 kW rated9,000–18,000 rpmER25Water-cooledØ110 mmKeep the 2.2 kW rated entry separate from the 4.4 kW curve line and S1/S6-20%, TA20°C notes.
GDK125-12-24Z/7.57.5 kW rated12,000–24,000 rpmER32Water-cooledØ125 mmCheck 7.5 kW rated, 15 A and the full 400–800 Hz relationship with the proposed drive.
GDK125-30Z/7.57.5 kW rated30,000 rpm ratedER32Water-cooledØ125 mmCheck 380 V / 15 A and 1,000 Hz as motor-output requirements, separate from drive input supply.
GDK125-9-15Z/5.5-115.5 kW rated9,000–15,000 rpmER32Water-cooledØ125 mmKeep 5.5 kW rated separate from the 11 kW curve level and S1/S6-20%, TA20°C notes.
GDK58-24Z/0.80.8 kW rated24,000 rpm ratedER11Water-cooledØ58 mmCheck 220 V / 3 A and 400 Hz as motor-output requirements, separate from mains supply.
GDK80-12-24Z/1.2-2.41.2 kW rated12,000–24,000 rpmER20Water-cooledØ80 mmKeep 1.2 kW rated separate from the 2.4 kW graph line and S1/S6-20%, TA20°C notes.
GDK80-24Z/1.51.5 kW rated24,000 rpm ratedER16Water-cooledØ80 mmKeep 220 V / 5.6 A and 380 V / 3 A as complete separate winding pairs.
GDK80-24Z/2.22.2 kW rated24,000 rpm ratedER20Water-cooledØ80 mmKeep 220 V / 7.6 A and 380 V / 4.4 A as separate supplied winding choices.
GDK85-24Z/2.2D2.2 kW rated24,000 rpm ratedER20Water-cooledØ85 mmKeep 220 V / 7.6 A and 380 V / 5.5 A as separate supplied winding choices.

ALL SPINDLES

Compare GDK configurations.

Compare tooling, cooling and operating ratings, then open the exact configuration for your machine.

FILTER SPINDLES

Showing 13 configurations

More filters

Choose a winding voltage, not a voltage shown on a power curve. Ask us if the voltage you need is not listed.

GDK Engraving & Milling Spindles · 13 configurations

Spindles with model-specific operating ranges and power ratings. Read the duty conditions and VFD curve before choosing by power.

INSTALLATION FIRST

Check the exact model before ordering.

CONFIGURATION & QUOTATION

Request an HQD GDK spindle quote

Send the exact code, intended cutter speeds and load cycle, selected winding where listed, drive model and mounting evidence. Include water/air services, quantity, destination and tooling or additional curve/document needs.

A quotation requires the exact model and physical variant, selected winding, tooling, cooling requirements, quantity and destination. For a replacement, include the existing nameplate, mounting dimensions and equipment intended for reuse. CINKR confirms the proposed supply scope, availability and delivery terms by email.

Compare other HQD series

Compare all models →